Rainbow Ladder Bracelet

What You'll Need

Gold Tone 13mm Bar & Link Chain - By The Foot
CHA-1015	Project uses 3 feet. Product Discontinued

Gold Tone Cable Chain 3.5mm x 4.5mm - By The Foot
CHA-1013 BrandID:28	Project uses 1 foot. This item is sold by the foot. Price: $2.75 / foot	Quantity:

22K Gold Plated Open Jump Rings 7mm 18 Gauge (x100)
FJR-5270 BrandID:28	Project uses 5 pieces.  You will need 1 package. 1 package = 100 Pieces Price: $6.25 / pkg	Quantity:

22K Gold Plated Open Eye Pins 21 Gauge 2 Inches (x50)
FHP-6220 BrandID:28	Project uses 7 pieces.  You will need 1 package. 1 package = 50 Pieces Price: $5.40 / pkg	Quantity:

22K Gold Plated Head Pins - 22 Gauge, 2 Inches (X50)
FHP-5221 BrandID:28	Project uses 15 pieces.  You will need 1 package. 1 package = 50 Pieces Price: $4.29 / pkg	Quantity:

Beautiful Gold Plated Curved Lobster Clasps 10mm (10)
FCL-2514 BrandID:28	Project uses 1 piece.  You will need 1 package. 1 package = 10 Pieces Price: $4.67 / pkg	Quantity:

Gemstone Bead Lot Mix 4mm Round Beads /16 Inch Strand
SPMX-54 BrandID:28	Project uses 42 pieces.  You will need 1 package. 1 package = 1 Strand Price: $3.83 / pkg	Quantity:

Gemstone Bead Lot Mix 6mm Round Beads /15.5 Inch Strand
SPMX-56 BrandID:28	Project uses 15 pieces.  You will need 1 package. 1 package = 1 Strand Price: $4.07 / pkg	Quantity:

Instructions:

1. Cut five lengths of the bar and link chain 6 ½ inches long. Be sure to leave the smaller links on either end.


2. Cut one length of the CHA-1013 chain approximately 2 inches long.


3. Starting with an eyepin, add 4mm bead.


4. Thread eyepin through the small link at the end of one of the 6 ½ inch chain lengths.


5. Add another 4 mm bead.


6. Repeat these steps, adding to the same eyepin: 4mm bead, small link at the end of a 6 1/2" chain, 4mm bead, small link at the end of a 6 1/2" chain, etc.. until you have 6 beads on the eyepin with the five 6 1/2" pieces of chain hanging between them.


7. When you get to the other end of the eyepin, create a simple loop, but be sure to leave a lot of wiggle room so the beads and chain don't get too cramped on the eyepin (the eyepin should be about 1 ½ inches wide).


8. Repeat this process, threading your eyepins through the 4mm beads and small links of the five pieces of chain, skipping every other small links. It is very important to thread the eyepin through the same side of each link, so that the bracelet doesn't become tangled.


9. Using the headpins, make fifteen 6mm bead drops with a simple loop.


10. Attach one of these to each end of the beaded eyepins, using the proper way to open and close a jump ring. The extra one is for the end of the extender chain.


11. Add two jump rings to the middle of each end of the bracelet, straddling the middle chain.


12. To one end, add another jump ring connecting the two, then add a lobster clasp.


13. To the other end, add the 2 inch length of chain to the two jump rings and finish at the end with the final 6mm bead.