|
Midnight Garden Bracelet
Project B614
Designer: Julie Bean
While wearing this bracelet, imagine yourself sitting on an iron bench at midnight in an overgrown garden
surrounded by night blooming flowers. Rich tones of brass, purple, and green swirl around your wrist,
wrapping you in beauty.
|
What You'll Need
Purchase All Supplies
Specialized Tools
|
Instructions:
- Onto a head pin, place 1 Toho 11/0 seed bead in rainbow lt. topaz/sea foam lined, 1 lucite marigold flower in lt. amethyst, 1 Swarovski 10mm margarita bead in erinite. Create a after the last bead. Cut off excess wire with flush cutters. Create another 2 of these.
-
Onto a head pin, place 1Toho 11/0 seed bead in rainbow lt. topaz/sea foam lined, 1 lucite marigold flower in lt. amethyst, 1 Swarovski 14mm margarita bead in jet black, and 1 Vintaj brass fastenable filigree flower. Create a wrapped wire loop right after the filigree. Make another 2 of these.
-
Cut 3 lengths of beading wire, 11 inches long each. Place a bead stopper on the end of each wire, 3 inches from the tail.
-
We are going to bead all these wires at the same time. Make sure to keep placing bead stoppers on the strand ends as switch back and forth between the three strands. Onto each of the beading wires, bead 1 brass crimp bead.
-
Now bead 1 inch of seed beads, mixing in some rainbow lt. topaz/sea foam lined Toho seed beads in with the Czech purple passion seed bead mix. Pass the end of each wire through the wrapped wire loop at the base of one of the clusters you made in step 1 and also one of the clusters you made in step 2. Next, pass the beading wires through the hole in the middle of 1 Swarovski 8mm round jet bead. Repeat this step another 2 times.
-
Take a pause for a moment and make sure to place a bead stopper on the end of each of your strands.
-
Cut the head off a head pin. Do not cut off any more of the wire length then you need to to remove the head. Create a wrapped wire loop on the end of the head pin that no longer has a head.
-
Go back to your beadwork and bead another inch of mixed seed beads onto each of the three beading wires. Pass all three wires through the hole in the middle of 1 Swarovski 10mm margarita bead in erinite and 1 Swarovski 8mm round jet bead. Now string a crimp bead on each of the strands. Take one of the strands and loop the beading wire through the wrapped wire loop you made in the previous step, pull it back around and through the crimp bead and the jet black round bead, pull snug. . Do this with the other two strands.
-
Onto the wire sticking out of your wrapped wire loop which you just attached all the strands to, thread on 1 Vintaj brass ornate filigree bead cap (with the bead cap facing the Swarovski round bead in jet and hiding the wrapped wire loop). Next place onto the wire 1 Swarovski 10mm margarita bead in erinite, 1 lucite marigold flower in lt. amethyst, and 1 Toho 11/0 seed bead in rainbow lt. topaz/sea foam lined. Create a wrapped wire loop after the last bead. Onto the wrapped wire loop, and link 1 4mm jump ring and also the hoop at the base of the brass lobster clasp. Close the jump ring.
-
We are now going to complete the other side of the bracelet. First, thread onto a head pin: 1 Toho 11/0 seed bead in rainbow lt. topaz/sea foam lined, 1 lucite marigold flower in lt. amethyst. Make two of these. Thread onto another head pin 1 Toho 11/0 seed bead in rainbow lt. topaz/sea foam lined and 1 Swarovski 14mm margarita bead in jet black.
-
Locate your Vintaj brass circle filigree pendant and push the pin part of the head pin with the black margarita bead on it through the holes in the side of the filigree. Pull the wire through to the other side and carefully create a wrapped wire loop to secure it in place. Cut off excess wire with flush cutters. Now repeat the same process with the two lucite flower adorned head pins you made in the previous step. Position one on each side of the black margarita bead you just attached.
-
Time to attach your strands. Take one strand of beads from your bracelet body and remove the bead stop. Pull it under the circle pendant and through the wrapped wire loop on one of the lucite flowers. Pull the beading wire back around and through the crimp bead and several beads next to it. Pull snug and crimp the bead. Repeat this same process with another bead strand from the bracelet and the other lucite flower wrapped wire loop. Finally, take your third strand and instead of going under the circle filigree, go over it and fasten this strand to the wrapped wire loop at the base of the large Swarovski black margarita bead.
-
Thread onto another head pin, 1 purple seed bead and 1 Swarovski 10mm margarita bead in erinite. Create a simple wire loop right after the margarita bead. Cut off excess wire with flush cutters. Open the simple wire loop and attach it to the wrapped wire loop which you attached the third bracelet strand to.
-
Now an 8mm brass jump ring and place it around the neck of the head pin holding the black margarita bead to the filigree circle (you want to position it right where the jet black bead meets the filigree). Close the jump ring.
-
Open another 8mm brass jump ring and link it to the jump ring you just attached. Close the jump ring back up. This is the other half of your clasp.
-
You're finished! Enjoy!
|
Tip: Check package quantities for each component. You may have extra material to make more than one finished project, or will have leftovers for other projects. In some cases, adding on just one more package of a component may be all you need to make multiple pieces.
All designs © Beadaholique Inc.
You may use our designs to make items for personal use or gifts.
Sale of our designs, whether in written form or assembled, is prohibited.
|
|
Enlarge Photo
Enlarge Photo
