|
Shades of Fall Necklace
Project N511
Designer: Kathy Mannix
The leaves of fall bring warmth to this Swarovski crystal and Vintaj brass necklace.
|
What You'll Need
Purchase All Supplies
Specialized Tools
|
Instructions:
-
First, make the leaf dangles. Thread a red Swarovski crystal bicone (SWC-1388), a brass daisy washer (PND-7265), and the red Lucite leaf (BCP-4312) onto a headpin (FHP-6301). Make a wire loop wrap. Trim off excess wire. Set aside.
-
Thread a yellow Swarovski crystal bicone (SWC-1369), a brass daisy washer, and a yellow Lucite leaf (BCP-4311) onto a headpin. Make a wire loop wrap. Trim off excess wire. Set aside.
-
Thread a brown Swarovski crystal bicone (SWC-13054), a brass daisy washer, and a brown Lucite leaf (BCP-4323) onto a headpin. Make a wire loop wrap. Trim off excess wire. Set aside.
-
Now, move on to the Cubic Zirconia dangles. Cut 3 pieces of brass chain, 2 inches in length, 1 and 1/4 inches in length, and 1 and 3/4 inches in length. Set aside.
-
Cut a piece of 26 gauge wire (WCR-4226) 6 inches in length. Wire wrap a small red cubic zirconia briolette (LINK). Open the end link of the piece of brass chain (CHA-7140) 2 inches in length. Link the briolette you just wire wrapped onto the open link of chain. Close link. Set aside.
-
Cut a piece of 26 gauge wire (WCR-4226) 6 inches in length. Wire wrap a small orange cubic zirconia briolette (SPCZ-58). Open the end link of the piece of brass chain (CHA-7140) 1 and 1/4 inches in length. . Link the briolette you just wire wrapped onto the open link of chain. Close link. Set aside.
-
Cut a piece of 26 gauge wire (WCR-4226) 6 inches in length. Wire wrap a small yellow cubic zirconia briolette (SPCZ-365). Open the end link of the piece of brass chain (CHA-7140) 1 and 3/4 inches in length. Link the briolette you just wire wrapped onto the open link of chain. Close link. Set aside.
-
Open a medium plain brass jump ring (FJR-5372). Thread through the end link of each of the pieces of chain with the wire wrapped cubic zirconia briolettes. Close jump ring. Set aside.
- Place the large brass maple leaf on top of a 4x4 steel block (XTL-6092). Take the texturizing hammer (XTL-0257), with diamond shaped end and gently hammer on the top of the entire brass maple leaf. Set aside.
-
Open a large plain jump ring (FJR-5331). In this order, link through the hole of the large brass maple leaf (PND-7218), the hole of the medium brass leaf (PND-7218), the medium jump ring with the 3 pieces of chain and cubic zirconia briolettes, the loop of the yellow Lucite leaf, the loop of the brown Lucite leaf, and the loop of the red Lucite leaf. Close jump ring.
-
Open another plain medium brass jump ring (FJR-5372). Link through the large plain jump ring with the assembled leaf and chain pieces. Close jump ring.
-
Open one of the twisted brass jump rings (FJR-5395). Link through the Swarovski cosmic ring pendant (SWC-9036). Close jump ring.
-
Open the other twisted brass jump ring (FJR-5395). Link through the medium brass jump ring from the assembled leaf and chain piece and the Swarovski cosmic ring pendant (see photo). Close jump ring.
-
Fold the other brass chain (CHA-7115) in half to find the center link. Open the center link of the chain and link onto the other twisted jump ring attached to the cosmic ring pendant. Close the link.
-
Open the large plain jump ring from the clasp (FCL-4641). Thread through one of the end links of the chain. Close jump ring.
-
Open the end loop of the swirl clasp (FCL-4641). Link through the other end link of the chain. Close loop.
-
Open a small brass jump ring (FJR-5340). Link through the hole of the small brass leaf (PND-7104) and the end link of chain with the swirl clasp. Close jump ring. You're finished!
Please refer to photo for more detailed information about this project.
Keywords: autumn, btq-nature
Tip: Check package quantities for each component. You may have extra material to make more than one finished project, or will have leftovers for other projects. In some cases, adding on just one more package of a component may be all you need to make multiple pieces.
All designs © Beadaholique Inc.
You may use our designs to make items for personal use or gifts.
Sale of our designs, whether in written form or assembled, is prohibited.
|
|
